Table of contents
Model | Material | Thickness | Technical characteristics | Quote |
---|---|---|---|---|
![]() |
ABIL | From 0,25 to 1,5 mm |
Technical characteristics of stamped parts: Dark grey, density 1.0; temperature + 120 °C, peak temperature + 150 °C, max. pressure 10 bar, compressibility 22.5 %, tensile strength 15 N / mm2, very good resistance to oil and fuel, good resistance to acids and alkalis. |
![]() |
![]() |
AFM 30 | From 0,25 to 3,0 mm |
Technical characteristics of stamped parts: Green, density 1.95; max. temp. + 250 °C, max. pressure 100 bar, good resistance to oil, fuel, acids and alkalis, DVGW approved (German gas and water specialists association), BAM, HTB (gas and heating test bed) tested. |
![]() |
![]() |
BUTYL® | From 1,0 to 10,0 mm |
Technical characteristics of stamped parts: 60 ± 5 Sh. A, black, density 1.11; temp. range - 40 to + 100 °C, tensile strength 13 MPa, tensile elongation 600 %, good resistance to acids, alkalis and ozone. |
![]() |
![]() |
CELLULAR VULKOLLAN® | From 1,0 to 60,0 mm |
Technical characteristics of stamped parts: Density 350 + 450 kg / m3, temp. range. - 20 to + 80 °C, good oil resistance, resistance to fuel conditional, weather resistant; RG 35 + RG 45. |
![]() |
![]() |
CENTELLEN 200 | From 0,5 to 5 mm |
Technical characteristics of stamped parts: Red, density 1.80; temp. range - 200 to + 180 °C, max. pressure 40 bar, good oil resistance, resistance to acids and alkalis conditional, KTW approved (plastic and rubber for drinking water). |
![]() |
![]() |
CENTELLEN WS 3820 | From 0,3 to 4,0 mm |
Technical characteristics of stamped parts: Green, density 1.80; temp. range - 200 to + 200 °C, max. pressure 100 bar, good oil resistance, resistance to acids and alkalis conditional, DVGW approved (German gas and water specialists association), BAM, KTW (plastic and rubber for drinking water), HTB (gas and heating test bed), WRC (water research centre). |
![]() |
![]() |
CER | From 2,0 to 60,0 mm |
Technical characteristics of stamped parts: Cellular epoxy rubber black, 45 ± 10 Sh., density 175 kg / m3; temp. range - 50 to + 95°C, peak temperature +100°C, resistance to alkalis, acids and oil conditional, very good ozone resistance, closed pores, FMVSS 302, SAE J 18- 79, ASTM D 1056-77, AFNOR, NF - R 99-211-80, DBL 5574.10. |
![]() |
![]() |
CRCR | From 2,0 to 50,0 mm |
Technical characteristics of stamped parts: CR cellular rubber 45 ± 10 Sh., black, density 175 kg / m3, temp. range. - 40 to + 80 °C, resistance to alkalis, acids, oil, fuel and ozone conditional, closed pores, FMVSS 302, SAE J 18-79, ASTM D 1056-77, AFNOR NF - R 99-211- 80, DIN 7726. |
![]() |
![]() |
EPDM 402 | From 1,0 to 20,0 mm |
Technical characteristics of stamped parts: 60 ± 5 Sh. A, black, smooth on both sides, density 1.06; temperature range : - 35 to + 100 °C, tensile strength 18 MPa, tensile elongation 400 %, very good resistance to alkalis and the ozone, low in nitrosamine, approved according to DIN 4807. |
![]() |
![]() |
EPDM 50 | From 1,0 to 40,0 mm |
Technical characteristics of stamped parts: Tc50 ± 5 Sh. A, black, density 1.06; temperature range: - 40 to + 100 °C, tensile strength 9 MPa, tensile elongation 500 %, good resistance to acids, alkalis and the ozone, paint neutral, meets VW 2.8.1. G50 standard and DBL 5556.10 standard (Daimler-Benz delivery rules). |
![]() |
![]() |
EPDM 60 | From 1,0 to 20,0 mm |
Technical characteristics of stamped parts: 60 ± 5 Sh. A, black, density 1.30; temperature range: - 40 to + 100 °C, tensile strength 5 MPa, tensile elongation 300 %, resistance to acids and alkalis conditional, also available with 1 or 2 duck layers. |
![]() |
![]() |
EPDM 80 | From 1,0 to 10,0 mm |
Technical characteristics of stamped parts: 80 ± 5 Sh. A, black, density 1.30; smooth on both sides, temperature - 40 to + 100 °C, tensile strength 5,8 MPa, tensile elongation 200 %, good resistance to acids and alkalis, very good weathering resistance. |
![]() |
![]() |
EPDM Heat | From 0,5 to 10,0 mm |
Technical characteristics of stamped parts: 50 ± 5 Sh. A, black, KTW, density 1.08; temperature range: - 40 to + 150 °C, tensile strength 12 MPa, tensile elongation 350 %, very good resistance to acids, alkalis and the ozone, meets VW 2.8.1. G50 standard and DBL 5571.20 standard (Daimler-Benz delivery rules), sulphur-free. |
![]() |
![]() |
FASERFLEX | From 0,2 to 3,0 mm |
Brown, density 0.80; temperature + 120 °C, very good resistance to oil and fuel. |
![]() |
![]() |
FIBRE | From 0,3 to 3 mm |
Technical characteristics of stamped parts Fibre: Red, hard, density 1.35; temperature + 95 °C, very good resistance to oil and fuel, resistance to alkalis and acids conditional, KTW (plastic and rubber for drinking water). Also available in grey or black. |
![]() |
![]() |
FRN | From 2,0 to 40,0 mm |
Technical characteristics of stamped parts: Foam rubber natural; density 350 - 750 kg / m3, dark grey, cellular blend; temp. range - 40 to + 70 °C, tensile elongation 250 - 400 %, resistance to oil, fuel, acids, alkalis and ozone conditional, motif on both sides. |
![]() |
![]() |
GU - KORK PR 82 | From 1,0 to 6,0 mm |
Technical characteristics of stamped parts: Red - brown PU, density 0.77; temperature + 110 °C, good resistance to oil, fuel, acids, alkalis, ozone and weather conditions. |
![]() |
![]() |
GU 40 GREY | From 0,5 to 20,0 mm |
Technical characteristics of stamped parts: 40 ± 5 Sh. A, grey, density 1.03; temp. range - 40 to + 70 °C, short-term peak temperature 80 °C, tensile strength 15 MPa, tensile elongation 500 %, good resistance to acids and alkalis, paint neutral, DVR 22 h / 70 °C / 35 %. |
![]() |
![]() |
GU 45 WHITE | From 1,0 to 10,0 mm |
Technical characteristics of stamped parts: No duck layer, 45 ± 5 Sh. A, white, density 1.27; temp. range - 30 to + 70 °C, tensile strength 12 MPa, tensile elongation 550 %, food grade, good resistance to alkalis, resistance to acids conditional, BGVV XXI (BGA) Cat. 1 FDA CFR 177.2600. |
![]() |
![]() |
GU 50 | From 1,0 to 40,0 mm |
Technical characteristics of stamped parts: 50 ± 5 Sh. A, black, density 1.30; temp. range - 35 to + 70 °C, tensile strength 4 MPa, tensile elongation 300 %, resistance to acids and alkalis conditional, DVR 24 h / 70 °C / 40 zz%. |
![]() |
![]() |
GU 52 RED | From 1,0 to 10,0 mm |
Technical characteristics of stamped parts: 50 ± 5 Sh., density 1.24; temp. range - 30 to + 90 °C, tensile strength 7 MPa, tensile elongation 500 %, food grade, resistance to acids and alkalis conditional. |
![]() |
![]() |
GU 67 LIGHT | From 1,0 to 20,0 mm |
Technical characteristics of stamped parts: 65 ± 5 Sh. A, KTW approved (plastic and rubber for drinking water), density 1.43; temp. range - 30 to + 70 °C, tensile strength 8 MPa, tensile elongation 380 %, food grade, good resistance to alkalis, resistance to acids conditional, BGVV XXI (BGA) Category 4. Also available with 1, 2 or 3 duck layers. |
![]() |
![]() |
GU 70 | From 0,5 to 50,0 mm |
Technical characteristics of stamped parts: 70 ± 10 Sh. A, black, density 1.45; temp. range - 30 to + 70 °C, tensile strength 4 MPa, tensile elongation 150 %, resistance to acids and alkalis conditional. Also available with 1 or 2 duck layers. |
![]() |
![]() |
GU 90 | From 1,0 to 6,0 mm |
Technical characteristics of stamped parts: 85 ± 5 Sh. A, black, density 1.40; temp. range - 30 to + 70 °C, tensile strength 5 MPa, tensile elongation 100 %, DVR (compression set) 24 h / 70 °C / 25 % resistance to acids and alkalis conditional. |
![]() |
![]() |
GU GAS | From 1,0 to 10,0 mm |
Technical characteristics of stamped parts: 80 ± 5 Sh. A, black, density 1.35; temp. range - 15 to + 80 °C, short-term peak temperature 110 °C, tensile strength 13 MPa, tensile elongation 250 %, DVR (compression set) 168 h / 100 °C / 35 %, good resistance to acids, alkalis, fuel and oil, ozone resistance conditional, DVGW approved according to standards DIN 3535 1 and 2 and DIN EN 549. |
![]() |
![]() |
GU GMSB | From 1,0 to 10,0 mm |
Technical characteristics of stamped parts: (GU grade for membranes and shot blasting) 60 ± 5 Sh. A, black, density 1.15; temp. range - 30 to + 70 °C, short-term peak temperature 90 °C, tensile strength 15 MPa, tensile elongation 400 %, good resistance to alkalis, DVR (compression set) 22 h / 70 °C / 30 %, volume resistivity < 106 |
![]() |
![]() |
HARD PVC | From 0,2 to 5,0 mm |
Technical characteristics of stamped parts Hard PVC: White, density 1.45; temp. range - 15 to + 60 °C, volume resistivity 103 |
![]() |
![]() |
HD - PE | From 0,5 to 6 mm |
Technical characteristics of stamped parts HD - PE: Natural, density 0.95; temp. range - 40 to + 80°C, volume resistivity 10162, very good resistance to acids and alkalis, good resistance to oil and fuel, KTW (plastic and rubber for drinking water). Also available in black. |
![]() |
![]() |
HD 300 | From 0,5 to 5 mm |
Technical characteristics of stamped parts: Green, density 1.90; max. temp. + 220 °C, max. pressure 80 bar, good resistance to oil and fuel, resistance to alkalis and acids conditional, KTW (plastic and rubber for drinking water), DVGW (German water and gas specialists association). |
![]() |
![]() |
HOSTAFORM C ( Delrin ) ( POM ) | From 0,5 to 6,0 mm |
Technical characteristics of stamped parts: Natural, density 1.41; temp. range - 40 to + 100°C, dielectric strength 50 kV / mm, special volume resistivity 10152, very good resistance to oil, fuel, acids and alkalis, UL 94 HB fi re classifi cation, hard, WRC (water research centre). |
![]() |
![]() |
HOSTAPHAN RN | From 0,01 to 0,35 mm |
Technical characteristics of stamped parts: Transparent, density 1.40; temp. range - 19O to + 130 °C, tensile strength 200 MPa, good resistance to oil, fuel, acids and alkalis. Modulus of elasticity 4500 N / mm2, tensile elongation 100 %, melting point 260 °C |
![]() |
![]() |
HYPALON | From 1,0 to 10,0 mm |
Technical characteristics of stamped parts: 70 ± 5 Sh. A, black, smooth on both sides, density 1.47; temp. range - 30 to + 120 °C, tensile strength 8 MPa, tensile elongation 180 %, very good resistance to alkalis and acids, good oil and ozone resistance. |
![]() |
![]() |
KLINGERSIL 4400 | From 0,3 to 5,0 mm |
Technical characteristics of stamped parts: Green, printed, density 1.6O; max. temp. + 400 °C, max. pressure 60 bar, good resistance to oil, alkalis, fuel and acids, HTB (gas and heating test bed), KTW (plastic and rubber for drinking water), WRC (water research centre), BAM, DVGW. |
![]() |
![]() |
KLINGERSIL C 4409 | From 0,8 to 3,0 mm |
Technical characteristics of stamped parts: Light green, density 2.0; max. temp. + 400 °C, max. pressure 80 bar, good oil resistance. |
![]() |
![]() |
LD - PE | From 0,1 to 6 mm |
Technical characteristics of stamped parts LD - PE: Natural, density 0.92; temp. range - 40 to + 60 °C, very good resistance to acids and alkalis, good resistance to oil and fuel, dielectric strength 75 Kv / mm, volume resistivity 10172, thermal conductibility 0.40 W / mxK, combustibility as per standard DIN 4102 B2. |
![]() |
![]() |
NEO 50 | From 1,0 to 20,0 mm |
Technical characteristics of stamped parts: 50 ± 5 Sh. A, black, density 1.20; temp. range - 20 to + 70 °C, tensile strength 6 MPa, tensile elongation 350 %, resistance to acids and alkalis conditional. |
![]() |
![]() |
NEO 60 LIGHT | From 1,0 to 10,0 mm |
Technical characteristics of stamped parts: 60 ± 5 Sh. A, light, density 1.46; temp. range - 20 to + 90 °C, tensile strength 6 MPa, tensile elongation 550 %, resistance to acids, alkalis and oil conditional, physiologically inert. |
![]() |
![]() |
NEO 63 | From 0,5 to 10,0 mm |
Technical characteristics of stamped parts: 65 ± 5 Sh. A, black, no duck layer, density 1.40; temp. range - 30 to + 70 °C, tensile strength 6 MPa, tensile elongation 200 %, resistance to oil, alkalis and acids conditional, good ozone resistance. DVR (compression set) 22 h / 70 °C / 40 %. Also available with 1 or 2 duck layers. |
![]() |
![]() |
NEO 80 | From 1,0 to 15,0 mm |
Technical characteristics of stamped parts: 80 ± 5 Sh. A, black, density 1.50; temp. range - 20 to + 70 °C, tensile strength 5 MPa, tensile elongation 200 %, resistance to ozone, oil, alkalis and acids conditional. |
![]() |
![]() |
NFR | From 2,0 to 30,0 mm |
Technical characteristics of stamped parts: Neoprene foam rubber, motif on both sides, density 700 - 1000 kg / m3, cellularblend, temp. range. - 40 to + 110 °C, resistance to acids, alkalis and oil conditional, self-extinguishing. |
![]() |
![]() |
NOBEST | From 1,5 to 10,0 mm |
Technical characteristics of stamped parts: Light, density 0.90; temperature + 1200 °C, tensile strength 3 MPa, good resistance to oil, fuel, acids and alkalis, loss on ignition 20 % max., other grade available on request. |
![]() |
![]() |
NSF | From 3,0 to 4,0 mm |
Technical characteristics of stamped parts: Fine weave. Black, 65 ± 5 Sh. A, density 1.45; temp. range - 30 to + 70 °C, tensile strength 4 MPa, tensile elongation 150 %, smooth bottom, fi ne grooves, resistance to acids and alkalis conditional. Also available with 1 duck layer. |
![]() |
![]() |
PERB 45 | From 1,0 to 20,0 mm |
Technical characteristics of stamped parts: 50 ± 5 Sh. A, black, density 1.30; temp. range - 10 to +70 °C, short-term peak temperature 80 °C, tensile strength 4 MPa, tensile elongation 350 %, DVR (compression set) 22 h / 70 °C / 40 %, resistance to acids and alkalis conditional, good oil resistance. |
![]() |
![]() |
PERB 60 LIGHT | From 1,0 to 10,0 mm |
Technical characteristics of stamped parts: 60 ± 5 Sh. A, light, density 1.32; temp. range - 30 to + 80 °C, tensile strength 11 MPa, tensile elongation 500 %, oil resistance conditional, food grade, good resistance to acids and alkalis, KTW approved (plastic and rubber for drinking water), BGVV XXI (BGA) cat. 2. |
![]() |
![]() |
PERB 65 | From 0,5 to 40,0 mm |
Technical characteristics of stamped parts: 65 ± 5 Sh. A, black, density 1.35; temp. range - 20 to + 70 °C, tensile strength 5 MPa, tensile elongation 200 %, DVR (compression set) 22 h / 70 °C / 40 %, good oil resistance, resistance to fuel, acids and alkalis conditional. Also available with 1 or 2 duck layers. |
![]() |
![]() |
PERB 80 | From 1,0 to 15,0 mm |
Technical characteristics of stamped parts: 80 ± 5 Sh. A, black, density 1.50; temp. range - 20 to + 70 °C, tensile strength 5 MPa, tensile elongation 200 %, resistance to ozone, oil, alkalis and acids conditional. |
![]() |
![]() |
PERB SUPER | From 0,8 to 10,0 mm |
Technical characteristics of stamped parts: 65 ± 5 Sh. A, black, density 1.37; temp. range - 20 to + 120 °C, tensile strength 7 MPa, tensile elongation 320 %, resistance to acids, alkalis and ozone conditional, very good resistance to oil and fuel. |
![]() |
![]() |
POLYAMIDE 6 ( Nylon ) | From 0,2 to 6 mm |
Technical characteristics of stamped parts Polyamide 6 (nylon): Natural, density 1.14; temp. range - 30 to + 100 °C, very good resistance to oil and fuel, good resistance to alkalis, resistance to acids conditional, hard, resists friction, good vibration damping properties, UL 94 - V2 fi re classifi cation, volume resistivity 1015 ohm.cm. |
![]() |
![]() |
POLYSTYROL | From 0,3 to 6,0 mm |
Technical characteristics of stamped parts Polystyrol: White, black, density 1.05; max. temp. + 70 °C, good resistance to acids and alkalis, oil resistance conditional, volume resistivity 1016 |
![]() |
![]() |
POLYURETHAN (PU) | From 0,5 to 50,0 mm |
Technical characteristics of stamped parts polyurethan (PU): 72 / 80 / 90 ± 5 Sh. A, brown, density 1.24-1.25; temp. range - 10 to + 60 °C, tensile strength 44 - 48 MPa, tensile elongation 550 - 600 %, resistance to acids and alkalis conditional, very good resistance to oil and fuel, very low abrasion. |
![]() |
![]() |
PTFE ( Teflon ) | From 0,05 to 40,0 mm |
Technical characteristics of stamped parts PTFE (Teflon): White, pure, density 2.18; temp. range - 200 to + 260 °C, volume resistivity 1018 |
![]() |
![]() |
SI 40 TR/RL | From 0,5 to 10,0 mm |
Technical characteristics of stamped parts: 40 ± 5 Sh. A, transparent, density 1.12; temp. range - 60 to + 230 °C, tensile strength 4 MPa, tensile elongation 300 %, good resistance to acids, alkalis and ozone, oil resistance conditional, food grade, BGA XV- Silicone, FDA # 177.2600. 6 - 8 cm = 50 ± 5 Sh. A. |
![]() |
![]() |
SI 60 RED | From 0,5 to 10,0 mm |
Technical characteristics of stamped parts: 60 ± 5 Sh. A, red, density 1.17; temp. range - 60 to + 230 °C, tensile strength 5 MPa, tensile elongation 250 %, good resistance to acids, alkalis and ozone, resistance to oil and fuel conditional, food grade, BGA XV- Silicone, FDA # 117.2600. |
![]() |
![]() |
SI 60 TR/RL | From 0,5 to 10,0 mm |
Technical characteristics of stamped parts: 60 ± 5 Sh. A, transparent, density 1.14; temp. range - 60 to + 230 °C, tensile strength 5 MPa, tensile elongation 250 %, food grade, good resistance to acids, alkalis and ozone, resistance to oil and fuel conditional, BGA XV- Silicone, FDA # 177.2600. |
![]() |
![]() |
SOFT PVC 70 | From 0,1 to 10,0 mm |
Technical characteristics of stamped parts soft PVC 70: 67 ± 5 Sh. A, natural, density 1.34; temp. range - 35 to + 50 °C, tensile elongation 260 %, resistance to acids conditional, good resistance to alkalis and oil, volume resistivity 1015 |
![]() |
![]() |
SOFT PVC 80 | From 0,3 to 10,0 mm |
Technical characteristics of stamped parts soft PVC 80: 80 ± 5 Sh. A, light and transparent, density 1.23; temp. range - 30 to + 80 °C, resistance to acids and alkalis conditional, UV-resistant. |
![]() |
![]() |
UNI-BLUE ASBESTOS FREE | From 0,3 to 5 mm |
Technical characteristics of stamped parts: Blue, density 1.80; temperature + 250 °C, pressure 100 bar, good resistance to oil and fuel, resistance to acids and alkalis conditional, KTW (plastic and rubber for drinking water), DVGW (German water and gas specialists association), WRC (water research centre). Also available with graphite on both sides. |
![]() |
![]() |
VITON® | From 1,0 to 6,0 mm |
Technical characteristics of stamped parts: 70 ± 5 Sh. A, black, density 1.92; temp. range - 20 to + 200 °C, tensile strength 6 MPa, tensile elongation 340 %, very good resistance to acids, oil and fuel, good resistance to alkalis, ozone and ageing resistant, pure FKM blend, high chemical resistance, good mechanical properties. |
![]() |
![]() |
VITON® TRIMMINGS | From 0,5 to 12,0 mm |
Technical characteristics of stamped parts: 75 ± 5 Sh. A, black, density 2.0; temp. range - 10 to + 275 °C, tensile strength 9 MPa, tensile elongation 200 %, DVR (compression set) 22 h / 200 °C / 45 %, good resistance to acids, alkalis, fuel, oil and ozone, sulphur-free, self-extinguishing, biphenol, electric insulation. |
![]() |
![]() |
VULKOLLAN® | From 0,5 to 50,0 mm |
Technical characteristics of stamped parts: 70 / 82 / 90 ± 5 Sh. A, natural, density 1.24 - 1.26; temp. range - 25 to + 80 °C, tensile strength 40 - 46 MPa, tensile elongation 620 - 660 %, good resistance to oil, fuel and ozone, resistance to acids and alkalis conditional. |
![]() |